| CHEMICAL
ANCHORS: INJECTION TYPE
EPX-5K 100% pure epoxy resin for threaded rod or rebar fixing
Volume 400 ml.
SANKO
EPX-5K, it is specially formulated chemical anchor
based on 100% pure epoxy resin, quick loading, no shrinking, and
ideals for hot climate. The product can be stored even at temperatures
above 30° C. SANKO EPX-5K has the strong bonding to the concrete
and good performance in oversized holes. Application into wet
concrete or diamond cored hole does not affect its performance.
|
APPLICATIONS:
Generator foundation,
Heavy duty machine,
Jib crane,
Automobile lift,
Electrical power pole,
Antenna tower,
Floor slab connection,
Wall and beam connections,
Column connections,
Structural repairing,
Structural staircases,
And etc. |
| USING THE CARTRIDGE: |
| |
1. Unscrew the cap
and take out the plug. |
| |
2. Pull piston
back and place cartridge into gun. Check the ejection of resin
and hardener. |
 3.
Screw on mixing nozzle. Do not use the first few centimeters
of mixture (until the color of mixture change to be steady
gray color). |
|
| INSTALLATION INSTRUCTIONS: |
 |
1.
Drill the hole. |
 |
2. Thoroughly
clean the hole to remove the dust by using a wire brush
and a puffer. |
 |
3. Apply
nozzle to the hole. Work from the bottom outwards until
it fills approximately half of the hole. |
 |
4. Insert
steel bar into the resin. Slowly rotate it by hand. |
| 
|
5. Wait
until it is full curing (see table). |
|
|
|
| CURING
TIME:
|
| Temperature
|
Approx.
curing start |
Approx.
full curing time |
| °C |
°F |
| 5 |
41 |
30 min |
8
hrs |
| 10 |
50 |
15 min |
6
hrs 30 min |
| 15 |
59 |
12 min |
5
hrs |
| 20 |
68 |
10 min |
3
hrs 30 min |
| 25 |
77 |
6 min |
2
hrs 45 min |
| 30 |
86 |
4
min |
2
hrs |
| 35 |
95 |
3 min |
1
hrs 45 min |
|
|
|
SANKO EPX-5K INSTALLATION
TABLE
WITH REINFORCING BAR (REBAR)
| Norminal diameter
(d): mm |
DB8 |
DB10 |
DB12 |
DB16 |
DB20 |
DB25 |
DB32 |
DB40 |
| Minimum base material
thickness (hmin): mm |
120 |
150 |
180 |
240 |
300 |
360 |
480 |
600 |
| Standard embedment depth
(hnon): mm |
80 |
100 |
120 |
160 |
200 |
250 |
320 |
400 |
| Hole depth (hdep):
mm |
80 |
100 |
120 |
160 |
200 |
250 |
320 |
400 |
| Drill bit diameter (do):
mm |
10 |
12 |
14 |
18 |
22 |
28 |
38 |
45 |
| Minimum edge distance
(Cmin): mm |
40 |
50 |
60 |
80 |
100 |
125 |
160 |
200 |
| Minimum anchor spacing
(Smin): mm |
40 |
50 |
60 |
80 |
100 |
125 |
160 |
200 |
|
|
| Ultimate tension load (Nu,avg):
kN |
20 |
35 |
50 |
95 |
150 |
|
|
|
| Allowance tension working load (Nall):
kN |
4 |
7 |
10 |
19 |
30 |
|
|
|
| Filling volume :ml |
7.5 |
11.3 |
15 |
22.6 |
37.7 |
|
|
|
| Trigger No. |
1 |
1.5 |
2 |
3 |
5 |
|
|
|
| Number of fixing per cartridge (approx.):
nos |
|
|
|
|
|
|
|
|
|
|
|
SANKO EPX-5K INSTALLATION TABLE
WITH FOR THREADED RODS
(Steel Gr. 5.8 and concrete C20/25)
| Norminal diameter
(d): mm |
M8 |
M10 |
M12 |
M16 |
M20 |
M24 |
M30 |
M32 |
| Anchor length (L): mm |
100 |
125 |
150 |
200 |
250 |
300 |
|
|
| Minimum base material
thickness (hmin): mm |
120 |
150 |
180 |
240 |
300 |
360 |
|
|
| Standard embedment depth
(hnon): mm |
80 |
100 |
120 |
160 |
200 |
240 |
|
|
| Hole depth (hdep):
mm |
80 |
100 |
120 |
160 |
200 |
240 |
|
|
| Drill bit diameter (do):
mm |
10 |
12 |
14 |
18 |
22 |
26 |
|
|
| Minimum edge distance
(Cmin): mm |
40 |
50 |
60 |
80 |
100 |
120 |
|
|
| Minimum anchor spacing
(Smin): mm |
40 |
50 |
60 |
80 |
100 |
120 |
|
|
| Maximum fixturethickness
(FT,max): mm |
10 |
12 |
15 |
20 |
25 |
30 |
|
|
| Hexagon nut spanner width
(sw): mm |
13 |
17 |
19 |
24 |
30 |
36 |
|
|
|
|
| Ultimate tension load (Nu,avg):
kN |
20 |
35 |
50 |
95 |
150 |
200 |
|
|
| Allowance tension working load (Nall):
kN |
4 |
7 |
10 |
19 |
30 |
40 |
|
|
| Filling volume :ml |
7.5 |
11.3 |
15 |
22.6 |
37.7 |
60.3 |
|
|
| Trigger No. |
1 |
1.5 |
2 |
3 |
5 |
8 |
|
|
| Number of fixing per cartridge (approx.):
nos |
48 |
32 |
24 |
16 |
9 |
6 |
|
|
|
|
|
| Product
Code |
Nominal
Dia. |
Overall
Lenght
(mm) |
Embedment
Depth
(mm) |
Drill
Bit
Dia.
(mm) |
Max.
Fixture
Thickness
(mm) |
|
| TR-08100-58 |
M8 |
100 |
min. 55
rec. 80* |
10 |
10 |
Gr. 5.8 |
| TR-10125-58 |
M10 |
125 |
min. 70
rec. 100* |
12 |
12 |
Gr. 5.8 |
| TR-12150-58 |
M12 |
150 |
min. 85
rec. 120* |
14 |
15 |
Gr. 5.8 |
| TR-16200-58 |
M16 |
200 |
min. 115
rec. 160* |
18 |
20 |
Gr. 5.8 |
| TR-20250-58 |
M20 |
250 |
min. 140
rec. 200* |
22 |
25 |
Gr. 5.8 |
| TR-24300-58 |
M24 |
300 |
min. 170
rec. 240* |
26 |
30 |
Gr. 5.8 |
| TR-08100-A2 |
M8 |
100 |
min. 55
rec. 80* |
10 |
10 |
A2-70W
(SUS304) |
| TR-10125-A2 |
M10 |
125 |
min. 70
rec. 100* |
12 |
12 |
A2-70W
(SUS304) |
| TR-12150-A2 |
M12 |
150 |
min. 85
rec. 120* |
14 |
15 |
A2-70W
(SUS304) |
| TR-16200-A2 |
M16 |
200 |
min. 115*
rec. 160 |
18 |
20 |
A2-70W
(SUS304) |
| TR-20250-A2 |
M20 |
250 |
min. 140
rec. 200* |
22 |
25 |
A2-70W
(SUS304) |
| TR-24300-A2 |
M24 |
300 |
min. 170
rec. 240* |
26 |
30 |
A2-70W
(SUS304) |
* Recommend of embedment depth. |
ฆ
